Select:
DIN
EN
ISO
GB/T
UNI
NFE
ASME
WS
norm
搜索
搜索
x

W-02196 PIAS®,AW内六星沉头双翼自钻自攻钉

Wing-type drilling screw countersunk head with AW drive PIAS®
产品摘要:

供货标准:W-02196 PIAS®

参考标准:-

产品材质:碳钢

产品涂层:Flake zinc silver-grey

产品性能:咨询

广告地址:
W-02196
W-02196 PIAS SY
W-02196 PIAS SW
W-02196
W-02196 PIAS SY
W-02196 PIAS SW
产品描述
参数
近似标准
产品特点
其他相关
右侧栏

WING-TYPE DRILLING SCREW, COUNTERSUNK HEAD WITH AW DRIVE PIAS®

 

The self-drilling screw with up to 50% time savings when fastening wood to metal substructures, steel, LAFRE® silver-grey coated.

 

Nominal diameter: 6.3 mm Head type: Countersunk head 80 degree
Drill tip length: 6 mm Internal drive: AW30
Other standard: Company standard Thread type: UNC
Surface: Flake zinc silver-grey Min. recommended substructure thickness: 2 mm
Max. material thickness to be drilled through (metal): 6 mm Min./max. recommended installation speed (idling): 800-1200 rpm

 

 

供货范围

 

材料 材质 性能等级 涂层简称 表面处理 常规供货范围 RoHS 其他
碳钢 ST    Flake zinc silver-grey 非电解锌片涂层 ST 6.3    
               

 

*   本表所示W-02196 PIAS®,AW内六星沉头双翼自钻自攻钉数据仅供参考,与产品相关的标准、规格、涂层、性能等具体参数,请以我司实际报价和供货为准。

*   本页面产品以常规供货为主。

*   符合以下情形,需要与我司销售人员咨询:

    如需订购其他近似标准产品,请咨询。

    本表所示数据仅为常规供货范围,特殊订货产品,请咨询。

    涉及企业标准验收、特殊质量协议及要求、特殊证明,请咨询。

 

关键词:
W-02196 PIAS®
AW内六星沉头双翼自钻自攻钉
Wing-type drilling screw countersunk head with AW drive PIAS®
扫二维码用手机看
未找到相应参数组,请于后台属性模板中添加

自钻自攻螺钉的产品执行标准见下表:

 

  名称   GB 标准   ISO 标准   DIN 标准
  十字槽盘头自钻自攻螺钉   GB/T 15856.1   ISO 15481   DIN 7504-M
  十字槽沉头自钻自攻螺钉   GB/T 15856.2   ISO 15482   DIN 7504-O
  十字槽半沉头自钻自攻螺钉   GB/T 15856.3   ISO 15483   DIN 7504-R
  六角法兰面自钻自攻螺钉   GB/T 15856.4   --   --
  六角凸缘自钻自攻螺钉   GB/T 15856.5   ISO 15480   DIN 7504-K
  开槽六角凸缘自钻自攻螺钉   --   --   DIN 7504-L

Description

Cr(6)-free corrosion protection, approx. 500 h, no base metal corrosion (salt-spray mist test in accordance with DIN EN ISO 9227 - NSS)

Countersunk head with milled pockets, for processing in softwood. For use in hardwood, the variant with head Ø 12mm is suitable (type. 0219864..).

 

AW drive system:

  • Enhanced torque transmission
  • Longer life
  • Optimum centring
  • Better mounting output thanks to fatigue-free screwing in; the required contact pressure for transmission of the torques is considerably lower
  • Largest possible contact surface of bit in screw drive
  • Even force distribution prevents damage to the surface-protection coating and therefore ensures better resistance to corrosion

 

Notice

The recommendation for the maximum wood thickness lH was calculated with reference to the maximum attachment thickness lU of the substructure.

Wing-pias must be appropriately tested for usability for each application case. Only install using equipment with depth stop and claw coupling.

Drilling screws may only be used where dampness is not to be expected. For fasteners with a construction permit, the permit, and in particular Part 2 "Special regulations", must always be observed.

 

Usage

Instructions

  • Force feeding of the screw is prevented by the wings drilling out the wood
  • The core hole is drilled into the substructure. The wings break off upon contact with the metal
  • The first few turns of the screw cut the thread, the remainder of the screw then screws into the thread

 

    紧固件实用工具    

> WASI 常见表面涂层简介

> WASI 标准件的样册查询

> 紧固件产品标准对照查询

> 紧固件制造交付标准对比

> 双相不锈钢紧固件的介绍

    马上关注我们吧    

如想了解更多

请扫描二维码

 

 

产品描述
参数
近似标准
产品特点
其他相关
右侧栏

WING-TYPE DRILLING SCREW, COUNTERSUNK HEAD WITH AW DRIVE PIAS®

 

The self-drilling screw with up to 50% time savings when fastening wood to metal substructures, steel, LAFRE® silver-grey coated.

 

Nominal diameter: 6.3 mm Head type: Countersunk head 80 degree
Drill tip length: 6 mm Internal drive: AW30
Other standard: Company standard Thread type: UNC
Surface: Flake zinc silver-grey Min. recommended substructure thickness: 2 mm
Max. material thickness to be drilled through (metal): 6 mm Min./max. recommended installation speed (idling): 800-1200 rpm

 

 

供货范围

 

材料 材质 性能等级 涂层简称 表面处理 常规供货范围 RoHS 其他
碳钢 ST    Flake zinc silver-grey 非电解锌片涂层 ST 6.3    
               

 

*   本表所示W-02196 PIAS®,AW内六星沉头双翼自钻自攻钉数据仅供参考,与产品相关的标准、规格、涂层、性能等具体参数,请以我司实际报价和供货为准。

*   本页面产品以常规供货为主。

*   符合以下情形,需要与我司销售人员咨询:

    如需订购其他近似标准产品,请咨询。

    本表所示数据仅为常规供货范围,特殊订货产品,请咨询。

    涉及企业标准验收、特殊质量协议及要求、特殊证明,请咨询。

 

关键词:
W-02196 PIAS®
AW内六星沉头双翼自钻自攻钉
Wing-type drilling screw countersunk head with AW drive PIAS®
扫二维码用手机看
未找到相应参数组,请于后台属性模板中添加

自钻自攻螺钉的产品执行标准见下表:

 

  名称   GB 标准   ISO 标准   DIN 标准
  十字槽盘头自钻自攻螺钉   GB/T 15856.1   ISO 15481   DIN 7504-M
  十字槽沉头自钻自攻螺钉   GB/T 15856.2   ISO 15482   DIN 7504-O
  十字槽半沉头自钻自攻螺钉   GB/T 15856.3   ISO 15483   DIN 7504-R
  六角法兰面自钻自攻螺钉   GB/T 15856.4   --   --
  六角凸缘自钻自攻螺钉   GB/T 15856.5   ISO 15480   DIN 7504-K
  开槽六角凸缘自钻自攻螺钉   --   --   DIN 7504-L

Description

Cr(6)-free corrosion protection, approx. 500 h, no base metal corrosion (salt-spray mist test in accordance with DIN EN ISO 9227 - NSS)

Countersunk head with milled pockets, for processing in softwood. For use in hardwood, the variant with head Ø 12mm is suitable (type. 0219864..).

 

AW drive system:

  • Enhanced torque transmission
  • Longer life
  • Optimum centring
  • Better mounting output thanks to fatigue-free screwing in; the required contact pressure for transmission of the torques is considerably lower
  • Largest possible contact surface of bit in screw drive
  • Even force distribution prevents damage to the surface-protection coating and therefore ensures better resistance to corrosion

 

Notice

The recommendation for the maximum wood thickness lH was calculated with reference to the maximum attachment thickness lU of the substructure.

Wing-pias must be appropriately tested for usability for each application case. Only install using equipment with depth stop and claw coupling.

Drilling screws may only be used where dampness is not to be expected. For fasteners with a construction permit, the permit, and in particular Part 2 "Special regulations", must always be observed.

 

Usage

Instructions

  • Force feeding of the screw is prevented by the wings drilling out the wood
  • The core hole is drilled into the substructure. The wings break off upon contact with the metal
  • The first few turns of the screw cut the thread, the remainder of the screw then screws into the thread

 

    紧固件实用工具    

> WASI 常见表面涂层简介

> WASI 标准件的样册查询

> 紧固件产品标准对照查询

> 紧固件制造交付标准对比

> 双相不锈钢紧固件的介绍

    马上关注我们吧    

如想了解更多

请扫描二维码

 

 

1/1
浏览量:
0

W-02196 PIAS®,AW内六星沉头双翼自钻自攻钉

零售价
0.0
市场价
0.0
浏览量:
0
产品编号
ZK022
数量
-
+
库存:
0
1
详情
近似标准
产品特点
其他相关
右侧栏
英文名称:
Wing-type drilling screw countersunk head with AW drive PIAS®
产品摘要:

供货标准:W-02196 PIAS®

参考标准:-

产品材质:碳钢

产品涂层:Flake zinc silver-grey

产品性能:咨询

WING-TYPE DRILLING SCREW, COUNTERSUNK HEAD WITH AW DRIVE PIAS®

 

The self-drilling screw with up to 50% time savings when fastening wood to metal substructures, steel, LAFRE® silver-grey coated.

 

Nominal diameter: 6.3 mm Head type: Countersunk head 80 degree
Drill tip length: 6 mm Internal drive: AW30
Other standard: Company standard Thread type: UNC
Surface: Flake zinc silver-grey Min. recommended substructure thickness: 2 mm
Max. material thickness to be drilled through (metal): 6 mm Min./max. recommended installation speed (idling): 800-1200 rpm

 

 

供货范围

 

材料 材质 性能等级 涂层简称 表面处理 常规供货范围 RoHS 其他
碳钢 ST    Flake zinc silver-grey 非电解锌片涂层 ST 6.3    
               

 

*   本表所示W-02196 PIAS®,AW内六星沉头双翼自钻自攻钉数据仅供参考,与产品相关的标准、规格、涂层、性能等具体参数,请以我司实际报价和供货为准。

*   本页面产品以常规供货为主。

*   符合以下情形,需要与我司销售人员咨询:

    如需订购其他近似标准产品,请咨询。

    本表所示数据仅为常规供货范围,特殊订货产品,请咨询。

    涉及企业标准验收、特殊质量协议及要求、特殊证明,请咨询。

 

关键词:
W-02196 PIAS®
AW内六星沉头双翼自钻自攻钉
Wing-type drilling screw countersunk head with AW drive PIAS®
未找到相应参数组,请于后台属性模板中添加

自钻自攻螺钉的产品执行标准见下表:

 

  名称   GB 标准   ISO 标准   DIN 标准
  十字槽盘头自钻自攻螺钉   GB/T 15856.1   ISO 15481   DIN 7504-M
  十字槽沉头自钻自攻螺钉   GB/T 15856.2   ISO 15482   DIN 7504-O
  十字槽半沉头自钻自攻螺钉   GB/T 15856.3   ISO 15483   DIN 7504-R
  六角法兰面自钻自攻螺钉   GB/T 15856.4   --   --
  六角凸缘自钻自攻螺钉   GB/T 15856.5   ISO 15480   DIN 7504-K
  开槽六角凸缘自钻自攻螺钉   --   --   DIN 7504-L

Description

Cr(6)-free corrosion protection, approx. 500 h, no base metal corrosion (salt-spray mist test in accordance with DIN EN ISO 9227 - NSS)

Countersunk head with milled pockets, for processing in softwood. For use in hardwood, the variant with head Ø 12mm is suitable (type. 0219864..).

 

AW drive system:

  • Enhanced torque transmission
  • Longer life
  • Optimum centring
  • Better mounting output thanks to fatigue-free screwing in; the required contact pressure for transmission of the torques is considerably lower
  • Largest possible contact surface of bit in screw drive
  • Even force distribution prevents damage to the surface-protection coating and therefore ensures better resistance to corrosion

 

Notice

The recommendation for the maximum wood thickness lH was calculated with reference to the maximum attachment thickness lU of the substructure.

Wing-pias must be appropriately tested for usability for each application case. Only install using equipment with depth stop and claw coupling.

Drilling screws may only be used where dampness is not to be expected. For fasteners with a construction permit, the permit, and in particular Part 2 "Special regulations", must always be observed.

 

Usage

Instructions

  • Force feeding of the screw is prevented by the wings drilling out the wood
  • The core hole is drilled into the substructure. The wings break off upon contact with the metal
  • The first few turns of the screw cut the thread, the remainder of the screw then screws into the thread

 

    紧固件实用工具    

> WASI 常见表面涂层简介

> WASI 标准件的样册查询

> 紧固件产品标准对照查询

> 紧固件制造交付标准对比

> 双相不锈钢紧固件的介绍

    马上关注我们吧    

如想了解更多

请扫描二维码

 

 

相关产品

DIN 7504P - ISO 15482 - GB/T 15856.2
W-02158 PIASTA®,AW内六星沉头自钻自攻螺钉 用于木材与金属连接
W-021997,AW内六星沉头双翼自钻钉 用于木材与金属连接
W-02159 PIAS®,AW内六星沉头双翼自钻钉 用于木材与金属连接
EJ-FD1,盘头十字钻尾钉
EJ-FD2,十字沉头钻尾钉
WASI

 全国热线电话: 022-8882-9200

2019 万喜(天津)紧固件有限公司版权所有

津公网安备 12011202000453号